How To Install A Chain Saw Blade
The chain saw blades are an essential part of the machine. To ensure that the blade works properly and does not cause any damage, they must be installed correctly. This article will show you how to install a chainsaw blade. To get the job done correctly, there are only a few steps you should take. We’ll also share tips for keeping your chainsaw blade in top condition. Lets get started! !
How To Install A Chain Saw Blade
How To Install A Chain Saw Blade.
Before installing a chainsaw blade, make sure it is off and unplugged. It is unsafe to use a running or plugged in machine. It is also dangerous to work on a machine that suddenly turns on as you are doing your job. The saw will heat up so it needs to cool down before you start cutting.
To attach the new blade to your chainsaw bar, place your thumb in the middle. Next, you will need to grab one half of the new chainsaw blade with your hands and place it underneath your bar. Your teeth should be pointed downwards, or towards the place where you will actually cut wood with your machine. You can then use a screwdriver to tighten each bolt on top. This is a process that you should do by hand, as an impact driver can cause the nuts to be loosened.
After that, make sure you push the chain brake down to prevent it from grabbing again when you start your machine. Your blade should now be in its place and ready for use. If you take off a blade and put it on, you might have to reverse the steps. This is all you need to know about installing a chainsaw blade.
How To Replace A Chainsaw Chain
Before you replace a chainsaw’s chain, make sure it is unplugged and turned off. It is unsafe to use a running or plugged in machine. It is also dangerous to work on a machine that suddenly turns on as you are doing your job. The saw will heat up so it needs to cool down before you start cutting.
Step 1: Take out the old chainsaw chain
To begin, insert your thumbnail into one of the holes in the rivet heads on the chainsaw chain. To begin removing the rivet, rotate your thumbnail counterclockwise. This will act as an anchor to ensure that the rest of it doesn’t move too much. Next, grab a pair needle-nose scissors and grasp the head of the rivet. This will allow you to twist the rivet completely from your saw blade. Continue this process until you have removed all but one rivet.
Step 2: Let go of the chain tension
Then, you can release the chain tension by inserting the end of your chainsaw saw bar into the slot in your saw base. Next, look at the guidebar that runs parallel to it to see where you should place it to ensure it overlaps all teeth equally. Grab your wrench and place its curved tip between the two front teeth of the guide bar. Turn them counterclockwise several more times to loosen any chain slack. Once you have completed the first side, turn the wrench counterclockwise several times to release any chain slack.
Step 3: Install your new chainsaw chain
Now you can install your new chainsaw by grasping one end of the chainsaw chain with your thumb, and turning it clockwise to stop just before reaching the section of the guide bar that has the rivets. This will allow your guide bar to fit perfectly on the new chain. Next, grasp the ends of the chainsaw with one hand and the wrench in the second. Then insert the curved tip of the saw blade between the two teeth. Finally, turn the chain clockwise several times to tighten the chain. Once you have completed the first side, switch to the second side. Next, insert the curved tip of the wrench between the teeth on each side. Finally, tighten the screws with a pair or similar tools.
Step 4: Test your new chainsaw chain
Once you have completed this, it is time for you to test your chainsaw chain. Once everything is working properly, turn the chainsaw on. Although this step is not necessary, if the saw does not start up immediately you will need to adjust its tension. This can be done by either tightening or loosening the bar depending on how difficult or easy it was. To give their saw extra protection against future problems, some owners will retighten it after several uses. However, each owner can decide what is best for them.
Step 5: Reinstall your old chainsaw chain
After you’re satisfied with the new chainsaw, you can remove it and reinstall it. Then turn on your chainsaw to check its performance. It won’t fix a broken chain, but it will make it cut through wood better.
Safety Tips
Many people forget to properly lubricate their bolts before screwing them into place with the wrench. This is important because the saw blade could become dangerously loose if it is not properly lubricated. It can fly off the machine if it is not properly protected. Before you put them in your guide plate, make sure to use a little WD-40.
You will need to loosen the three bolts that hold the blade of your chainsaw. However, you must not take them off yet. To lift the chain, use whatever tool you have and push it against the metal bar that runs alongside the blade. You don’t want to use an impact driver. This can cause damage to your chainsaw blade by removing the nuts. To avoid injury, make sure your work area is clean before you start.
If your chainsaw blade is extremely dull, it could be that it cannot cut properly. To make your blade cut through wood more easily, you may need to sharpen it.
Final Thoughts
The center of the blade of a chainsaw is a circular hole. This hole should align with the bar’s center. You will need one hand to hold the bar in place and the other to push the blade into place. Before you begin cutting wood, ensure that there is no slack between the ends of your gripping. Once everything is in place, you can begin cutting.
